CCNA基础知识题(英文版）

来源：vlan9.com 作者：出处：巧巧读书 2007-12-12 进入讨论组

601. Identify the following command to configure a secret password to 'cisco'?
A.) Router(config)#enable password cisco secret B.) Router(config)#enable secret cisco

C.) Router(config)#enable secret password cisco D.) Router(config)#set secret = cisco

Ans B

602. Identify the effect of Ctrl-Z?
A.) Exits back to privileged exec mode B.) Disconnect from the router C.) Abort the
ping operation D.) Exits privileged exec mode

Ans A

603. Given an IPX network with redundant paths, what command will configure load
balancing?
A.) ipx load-balance B.) ip maximum-paths 2 C.) ipx maximum-paths 2 D.) ipx
load-share

Ans C

604. Identify the correct IGRP configuration?
A.) Router# router igrp 100
Router# network 10.0.0.0

B.) Router(config)#router igrp 100
Router(config-router)#network 10.0.0.0

C.) Router(config)# router igrp
Router(config-router)# network 10.0.0.0

Ans B

605. Identify the components in the following command 'interface serial0/1/1'
A.) Serial interface, port number 0, slot 1, port adapter 1 B.)
Serial interface, slot 1, port number 1, port adapter 0 C.)
Serial interface, slot 0, port adapter 1, port number 1

Ans C

606. Identify the command to view the configuration-register value?
A.) show register B.) display config-register C.) show config D.) show version
Ans D

607. Identify the 2 commands that save the running-config to a TFTP server?
A.) write running tftp B.) copy running network C.) copy running tftp D.) write network

Ans C D

608. Identify the mode reflected by the following prompt 'Router<boot>'?
A.) Setup B.) RXBoot C.) Boot mode D.) Privileged exec mode

Ans B

609. How do you disable CDP on the entire Router?
A.) Router#no cdp run B.) Rotuer(config-if)# no cdp enable C.) Router(config)# no cdp
enable D.) Router(config)# no cdp run

Ans D

610. What command can be used to test IPX connectivity?
A.) Ping 2e.000.0045.8923 B.) Ping 192.168.100.1 C.) Ping ipx 2e.0000.0045.8923 D.) Ipx
ping 2e.0000.0045.8923

Ans D

611. Identify the 2 commands that display the clock rate configured on the serial0
interface?
A.) show serial0 B.) show interface serial0 C.) show clock rate serial 0 D.) show controllers

serial 0 E.) show running-config

Ans B E

612. What is the command to copy the IOS image to a TFTP server?
A.) copy flash tftp B.) copy running-config tftp C.) copy ios tftp D.) copy startup-config tftp

Ans A

613 Identify the command that configures the bandwidth to 56K?

A.) Router(config-if)# bandwidth 56000 B.) Router(config-if)# bandwidth 56k C.)
Router(config)# bandwidth 56 D.) Router(config-if)# bandwidth 56

Ans D

614 Identify the command to configure DLCI 100 on an interface e0?

A.) Router(config)# frame-relay local-dlci 100 B.) Router(config)# frame-relay local-dlci
100 int e0 C.) Router(config-if)# frame-relay local-dlci 100 D.) Router(config-if)#
frame-relay local-dlci 100 int e0

Ans C

615. Identify the command to configure the router to boot from an alternate IOS
located in flash?
A.) boot system flash IOS.exe B.) boot system tftp IOS.exe 172.16.5.1 C.) boot system
alternate IOS.exe D.) boot system rom IOS.exe

Ans A

616 Identify the command to configure a description on an interface?

A.) Router> description Finance department B.) Router(config)# description Finance
department C.) Router(config-if)# description Finance department D.) Router#
description Finance department

Ans C

617. Identify the 2 commands that will display the status and information about
interface E0 only?
A.) show interface ethernet E0 B.) show interface E0 C.) show E0 D.) show int E0 E.)
show interface

Ans B D

618. In order to configure a Frame Relay subinterface with IP identify the 2
commands that must be configured on the physcial interface?

A.) Router(config-if)# encapsulation frame-relay B.) Router(config-if)# no ip address C.)
Router(config-if)#encapsulation subinterface frame-relay D.) Router(config)#
subinterface s0 encapsulation frame-relay

Ans A B

619 Identify the command to determine if an IP access-list is grouped on
interface e0?

A.) Router(config)# show ip interface e0 B.) Router> show ip interface e0 C.) Router#
show interface e0 D.) Router# show ip interface e0

Ans D

620 Identify the keystroke to position the cursor to the beginning of a command line?

A.) Ctrl-A B.)
Ctrl-Ins C.) Ctrl-B
D.) Ctrl-Z

Ans A

621. Identify the following components of the IPX address 2e.0000.0065.ed43
A.) Not a valid IPX address B.) Network = 2e, Subnet = 0000, Node = 0065.ed43 C.)
Network = 2e.0000, Node = 0065.ed43
D.) Network = 2e, Node = 0000.0065.ed43

Ans D

622. What is the syntax to add a banner to the Cisco router?
A.) motd banner #
B.) banner
C.) banner motd #
D.) banner #

Ans C

623. What is the command to allow you to type Tokyo instead of the IP address
172.16.30.1 to access a router named Tokyo?
A.) config t, ip host Tokyo 172.16.30.1 B.) config t, ip hostname Tokyo 172.16.30.1 C.)
config t, hostname Tokyo 172.16.30.1 D.) config t, ip hostname 172.16.30.1 Tokyo

Ans A

624. How do you disable advanced editing?
A.) terminal editing B.) terminal no editing C.) disable editing D.) no terminal editing

Ans B

625. Which of the following will show an extended access list 150?
A.) sh access-list B.) sh ip int C.) sh ip access-list 150 D.) sh access-list 150 extended

Ans A C B ( a bit)

626. You have a Class B network address divided into 30 subnets. You will add 25 new
subnets within the next year. You need 600 host IDs for each subnet. Which subnet
mask should you use?
A.) 255.254.0.0 B.)

255.192.0.0 C.)
255.255.252.0
D.) 255.255.248 0
Ans C

627. What is the syntax to use to configure the port on a Catalyst 5000 switch?
A.) slot port/type B.)
type slot/port C.) port
slot/type D.) port
type/slot

Ans A

628. What 3 sources can configuration commands be placed into RAM?
A.) HP Openview B.) Console C.) Vterminal D.) TFTP server E.) NVRAM

Ans B D E

629 Identify the true statements about the following access list:
Access-list 101 deny tcp 192.10.172.0 0.0.0.255 any eq 23 Access-list
101 permit ip any any

A.) This access list prevents the host 192.10.172.0 from telneting B.) This access list
prevents any telnet traffic from subnet 192.10.172.0/24 C.) This access list filters some
telnet access D.) This access list denies any telnet traffic to subnet 192.10.172.0/24 E.)
This access list is invalid F.) The netmask on the this access list is reversed

Ans B C

630. Given the IPX address 4a.0002.1111.a999, what is the network ID and what is the
node ID?
A.) net 4a host 0002.1111.a999 B.) net
a999 node 0002.1111 C.) net

0002.1111.a999 node 4a D.) net
0002.1111 node a999

Ans A

631 What command do you use to disable domain lookup?

A.) no domain-lookup B.)
domain no-lookup C.)
lookup no-domain D.) no
ip domain-lookup

Ans D

632 Which of the following are valid Cisco encapsulation type names?

A.) arpa = IPX Ethernet B.) novell-ether = IPX Ethernet_802.3 C.) snap = IEEE 802.2
SNAP on Ethernet, FDDI, and Token Ring D.) novell-fddi = IPX Fddi_Raw E.) sap =
IEEE 802.2 on Ethernet, FDDI, and Token Ring F.) hdlc = HDLC on serial interfaces

Ans B C E F

633 Which of the following is an invalid host address using a netmask of
255.255.255.192?

A.) 10.1.1.1 B.)

10.1.1.66 C.)
10.1.1.130 D.)
10.1.1.127
An D

634. Which of the following will apply IPX sap access list 1010 for incoming traffic,
assume you are at the interface configuration?
A.) ipx input-sap-filter 1010 in B.) ipx
input-sap-filter 1010 C.) ipx
access-group 1010 in D.) ipx
access-list 1010 in

Ans C

635. What command can you type to view the connections after telneting into
multiple routers simultaneously?
A.) sh users B.) sh
ports C.) sh host D.) sh
sessions

Ans D

636. Which of the following is a valid extended IP access-list?

A.) router(config)# access-list 101 permit tcp host 172.16.30.0 any eq 21 log B.)
router# access-list 101 permit tcp host 172.16.30.0 any eq 21 log C.)
router(config)# acess-list 101 permit any any 172.16.30.0 D.) router(config)#
access-list 101 permit ip host 172.16.30.0 any eq 21 log

Ans A

637. What is the command to manually enter a static route?
A.) IP route <default gateway> <subnet mask> network B.) IP route <destination
network> <default gateway> C.) IP route < destination network> <subnet mask> <default
gateway> D.) IP route <destination network> <subnet mask> <source network>

Ans C

638. What key do you use to view the last command?
A.) Ctrl+X B.)
Ctrl+Z C.) Ctrl+E
D.) Ctrl+P

Ans D

639. What 2 commands verify end to end communications?
A.) Trace B.) debug ip session C.) Ping D.) Route

Ans A C

640. Your Ethernet interface currently has the IP address of 1.1.1.1/24. You would like
it to have a second IP address of 2.2.2.2/24. Which command will do that?
A.) ip address 1.1.1.1 2.2.2.2 255.255.255.0 B.) ip address 2.2.2.2 255.255.255.0 secondary
C.) ip address 2.2.2.2 255.255.255.0 D.) This cannot be done, you can only have 1 IP
address per physical interface. E.) ip address 2.2.2.2 /24

Ans B

641. Which command listed below sets the banner message when someone
connects to the router?
A.) message #
B.) banner #
C.) login banner #
D.) description #
E.) login description #
F.) banner motd #

Ans

642. What should be the first command to create an access-list that prevents all users
on subnetwork 10.10.128.0, using subnet mask 255.255.192.0, from being able to
telnet anywhere?
A.) access-list 101 deny tcp 10.10.128.0 0.0.63.255 any eq telnet B.)
access-list 101 deny tcp 10.10.128.0 255.255.0.0 any eq telnet C.)
access-list 101 deny tcp 10.10.128.0 255.255.192.0 any eq telnet D.)
access-list 101 deny tcp 10.10.128.0 0.0.192.255 any eq telnet E.)
access-list 101 deny tcp 10.10.128.0 0.0.128.255 any eq telnet F.)
access-list 101 deny tcp 10.10.128.0 0.0.127.255 any eq telnet

Ans A

643. The Cisco Discovery Protocol (CDP) periodically sends out a multicast packet (at
layer 2). Which command will alter the default interval of 60 seconds?
A.) cdp hold 111 B.) cdp wait 111 C.) cdp interval 111 D.) cdp 111 E.) cdp timer 111

Ans E

644. Which command will start the process for a Cisco IOS file image upgrade?
A.) download B.) copy tftp flash C.) copy flash tftp D.) download flash E.) network

Ans

645. Which command allows a user to see previous commands?
A.) show command B.) CTRL-P C.) show history D.) CTRL-U E.) Up Arrow F.)
SHIFT-CTRL-6

Ans B E

646. Which command will display the IPX routing table?
A.) show routes B.) show routes ipx C.) show routes protocol=ipx D.) show ipx E.) show
ipx route

Ans E

647. What is the correct command line syntax for configuring a port on a 7000 or 7500
series Cisco router with a VIP card?
A.) port B.) port adapter/port C.) You can't put a VIP card in a 7000 or 7500 router. D.)
slot/port-adapter/port E.) slot/port F.) slot

Ans D

648. How do you view the routers current processor utilization?
A.) show version B.) show processes cpu C.) show running-config D.) show startup-config
E.) show cpu F.) show utilization

Ans B

649. Which command will enable debugging for IPX RIP updates?
A.) debug ipx B.) debug ipx rip C.) debug ipx rip activity D.) debug rip E.) debug ipx
packets

Ans C

650. There is an emergency fall-back 'skeleton' IOS stored in read only memory on all
Cisco routers. What command would make the router load the IOS from Read Only
Memory?
A.) reload rom B.) boot system rom C.) load ios bootflash D.) load ios rom E.) bootsystem
skeleton

Ans B

651. Which command would configure Interface E0 with an IP address of
12.23.4.5 using a Subnet mask of 255.255.255.0 ?
A.) ip address 12.23.4.5 255.255.255.0 B.) ip address 12.23.4.5 /24 C.) ip address 12.23.4.5
mask 255.255.255.0 D.) ip address 12.23.4.5 mask ff:ff:ff:0 E.) that is an invalid mask
for a class 'A' address

Ans A but B & D can be used if the router is configured through
Router#(config)ip netmask-format (bitcount | decimal | hexadecimal)

652. Which commands will restart the router?
A.) router#system exit B.) router >reload C.) router#shutdown D.) router#reload E.)
router#(config)reload F.) router#system restart

Ans B

653. How do you set the encapsulation type to PPP for an interface?
A.) encap ppp B.) ppp encapsulation C.) encapsulation ppp D.) encapsulation ppp enable
E.) ppp enable encapsulation

Ans A C

654. Which Standard IP Access list commands will deny only the source address
1.1.1.1?

A.) access-list 9 deny host 1.1.1.1 B.) access-list 9 deny 1.1.1.1 255.255.255.0 C.)
access-list 9 deny 1.1.1.1 0.0.0.0 D.) access-list 9 deny 1.1.1.1 0.255.255.255 E.)
access-list 9 deny 1.1.1.1 255.255.255.255

Ans A C

655. Assume that you are editing a line of text on a Cisco router. What
key-stroke combination would take you to the beginning of the line?
A.) CTRL-B
B.) CTRL-Z
C.) CTRL-<space>
D.) CTRL-A
E.) CTRL-<up arrow>
F.) CTRL-<right arrow>

Ans D

656. Which global configuration command will tell the router to load the IOS file
'IOS_filename' from FLASH memory at the next boot?
A.) boot system flash B.) boot system flash IOS_filename C.) boot system IOS_filename
flash D.) boot system tftp IOS_filename tftp_address E.) config-register 0x0102 IOS_
filename

657. Which command will display adjacent routers found by the Cisco Discovery
Protocol?
A.) show all B.) show cdp entry C.) show ip neighbors D.) show cdp neighbor detail E.)
show cdp neighbor F.) show neighbor

Ans B D E

658. Which command line option will determine what traffic is interesting enough
to establish a dialup connection?
A.) dialer map B.) dialer string C.) dialer in-band D.) dialer-list E.) dialer negotiation

Ans D

659. Which command switches from User mode to Privileged mode?
A.) login B.) privilege C.) admin D.) enable E.) enter F.) root

Ans D

660. Extended IP access-lists (100-199) can be used to control traffic. Which
command listed below will permit smtp mail to only host 3.4.5.6 ?
A.) It is not possible for SMTP traffic B.) access-list 102 permit tcp any host 3.4.5.6 eq
smtp C.) access-list 101 permit tcp any 3.4.5.6 0.0.0.0 eq 23 D.) access-list 102 permit
tcp any any eq smtp E.) access-list 101 permit tcp any 3.4.5.6 0.0.0.0 eq 25

Ans B E

661. Which command-line keywords are valid for choosing Frame-Relay LMI types?
A.) itu-t B.) dlci C.) ansi D.) rfc 1544 E.) cisco F.) q933a

Ans C E F

662. Which command will copy the routers configuration from NVRAM to a
Network file server?
A.) copy start tftp B.) copy start tftp server C.) copy tftp startup-config D.) copy
running-config tftp E.) copy startup-config tftp

Ans A E

663. Which commands would assign and enable IPX on an interface ?
A.) enable netware B.) enable novell-ether C.) router#(config)ipx routing D.) You must
first enable IPX globally and then assign the network number to the interface . E.)
enable ipx F.) router#(config-if)ipx network 4a

Ans C D F

664. I want to configure a serial interface on a 7500 with a VIP card. What global
config command would give me access to a serial interface on a 7500?
A.) int 1/0/0 B.) int s
1/0/0 C.) int s 1/1
D.) int s0.1 E.) int s1

Ans B

665. Which command will display Ethernet 0's IP address?
A.) display ip address e0 B.)
show ip interface e0 C.) show
address e0 D.) sh ip address e0
E.) show all

Ans B

666. After the command -- router igrp 200 -- what command would enable IGRP on
the router for interface E0, with an address of 157.89.4.4 and a mask of
255.255.255.0 ?
A.) network 157.89.4.0 255.255.255.1 B.) network 157.89.0.0 C.) router igrp * D.) router
igrp 157.89.0.1 E.) router igrp int e1 F.) router igrp 157.89.4.1

Ans B

667. Which command do you use to set the Privileged mode password to
'clearwater'?
A.) set password=clearwater B.) enable privilege password clearwater C.) enable
password clearwater D.) enable login clearwater E.) enable secret password clearwater
F.) ebable clearwater

Ans C

668. How would you set the clock rate to 64K, on interface serial 0, from the
interface configuration mode?
A.) clock rate 64000 B.) bandwidth 64 C.) clock 64 D.) rate 64 E.) clock rate 64k F.) clock
rate 64

Ans A

669. Given the following static route command, 'ip route 3.3.3.0 255.255.255.0
4.4.4.4 125', which portion represents the administrative distance?
A.) 3.3.3.0 B.) 255.255.255.0 C.) 4.4.4.4 D.) route E.) 125

Ans E

670. What does the following line for an access list do? 'access-list 101 deny tcp
3.4.5.0 0.0.0.255 any eq 23'
A.) deny all ftp traffic B.) deny all ftp traffic from subnet 3.4.5.0 C.) deny all telnet traffic
from subnet 3.4.5.0 D.) deny all ftp traffic to subnet 3.4.5.0 E.) deny all telnet traffic

Ans C

671. Although Cisco IOS 11.2 and later can auto-detect the LMI type in Frame
Relay, which command will force the LMI type to q933a?
A.) frame-relay lmi-type q933a B.) encapsulation frame-relay q933a C.) don't need to, it
is the default D.) encapsulation q933a E.) encapsulation frame-relay type=q933a

Ans A

672. Which command can verify Application Layer connectivity between 2 hosts?
A.) ftp B.) snmp C.) telnet D.) ping E.) traceroute

Ans C

673. Scenario: You created 2 access-lists for controlling telnet about a year ago, and
bound one of them to Serial 0. You can't remember which access-list you used.
Which command lets you see all access-lists on Serial 0 for telnet?
A.) show access-list B.) show ip int s0 C.) show access-list telnet D.) show telnet
access-list E.) show access-list s0 F.) show int s0

Ans B

674. Cisco routers can secure the enable password with a one-way hash algorithm.
What command would encrypt the enable password with the strong encryption
method?
A.) enable encrypt john B.) password john C.) enable secret john D.) enable password john
E.) secret john F.) enable password 5 john

Ans C

675. Which command will display the encapsulation type on interface serial 0?
A.) show interface s0 B.) show all C.) show int s0 encap D.) show encap s0 E.) show encap

Ans A

676. What command do you enter at the keyboard to begin a user mode session?
A.) Type 'CTRL-P'B.) Type 'login'C.) Just press <ENTER>. D.) Type 'enable'E.) Press
'Shift + Ctrl + 6' at the same time.

Ans C

677. You want to set the console password to ralph. What would be the first
command you need to execute from global configuration mode?
A.) line console 0 B.) enable password ralph C.) login password ralph D.) set password=
ralph E.) password ralph F.) login Ralph

Ans A

678. Which command displays the IPX SAP table?
A.) show ipx sap B.) show sap C.) show ipx interface D.) show ipx servers E.) show ipx

Ans D

679. Which command will display the current time on a Cisco router?
A.) show date B.) show clock C.) show running-configuration D.) show time E.) show
controllers

Ans B

680. The default routing protocol for IPX is IPX RIP. How do you view the
routing updates sent and received by the router?
A.) debug ipx routing B.) debug ipx routing activity C.) debug rip D.) show ipx routing E.)
sh ipx F.) debug ipx rip

Ans B

681. Using the access-list command, 'access-list 1 deny 2.2.2.2', what else must be done
to stop host 2.2.2.2 from sending any traffic out of physical interface E0, while still
allowing other traffic?
A.) In global mode, Add a line - 'access-list 1 permit 0.0.0.0 255.255.255.255'B.) On
interface E0, Add a line - 'access-group 1 in'C.) In global mode, Add a line - 'access-list 1
permit all'D.) On interface E0, Add a line - 'access-list 1 in'E.) On interface E0, Add a line -
'access-list 1 out'F.) On interface E0, Add a line - 'ip access-group 1'

Ans F

682. Which command do you use to set the Secret password to 'roundwood'?
A.) enable login roundwood B.) enable password roundwood C.) enable privilege

roundwood D.) enable secret= roundwood E.) enable secret login roundwood F.) enable
secret roundwood

Ans F

683. How do you find the parameters that you can use with the SHOW command?
A.) ? show B.) show ? C.) debug show D.) help E.) sh?

AnsB

684. Which command would show all Ethernet interfaces with IPX configured on
them?
A.) show interface ipx ethernet B.) show ipx interface C.) show ipx interface ethernet D.)
show ipx E.) show version F.) show run

AnsB F

685. If you have configured IPX on a Serial interface, which command would
display the IPX network and node address on the Serial 1 interface?
A.) show interface B.)
show ipx s1 C.) show
interface s1 D.) show
ipx int serial 1 E.)
show ipx int brief

Ans D

686. Which command line statement determines the number of seconds a dialup
connection can wait without any traffic before the router hangs up?
A.) dialler max-time B.)
dialler timeout C.) dialer
idle-timeout D.) dialer
hang-up E.)
disconnect-timer

687. The Cisco Catalyst 5000 switch supports full duplex. How would you enable it on
the second port of the card in slot 1?
A.) router(config-if)# duplex full B.) router(config)# duplex full C.) router(config-if)# set
port duplex D.) router(config)#port duplex = full E.) router(config-if)# set port 1/2 full

Ans A

688. Which command will enable CHAP authentication on a serial interface that is
using PPP?
A.) encapsulation chap B.) ppp chap C.) ppp enable chap D.) ppp encapsulation chap E.)
ppp authentication chap F.) ppp chap enable

Ans E

689. From Enable mode, a user types the letter 'C' and presses enter. There is more
than 1 command that starts with 'C'. What message would the router return?
A.) Nothing would be returned, the command is simply ignored.
B.) unknown command C.) ambiguous command. D.) Copy to?E.) Configured console
from console.

Ans C

690. You want a message to be displayed every time someone tries to log on to the
router. Which command is required to accomplish this task?
A.) motd#(message)# B.) banner motd(message) C.) banner motd#(message)# D.)
banner motd*(message) E.) banner login#(message)#

691. You create the following standard access-list
access-list 1 deny 1.1.1.1 access-list 1 deny 2.2.2.2 int e0 ip access-group 1 in

Which of the following statements are true, with regard to traffic flowing
into E0?

A.) This will stop IP packets with a source address of 1.1.1.1 only.
B.) This will stop all IP packets.
C.) This is an invalid configuration.
D.) This will stop no IP packets.
E.) This will stop IP packets with a source address of 2.2.2.2 only.
F.) This will stop IP packets with a source address of 1.1.1.1 and 2.2.2.2.

Ans D

692. The command 'debug ip rip' will do which of the following?
A.) Show Neighbor Info. B.) Display RIP routing updates. C.) Show routing table changes.
D.) Show all IP traffic. E.) This is not a valid router command. F.) Cause the router to
respond with 'Ambiguous command'

Ans B

693. You would like to have a notation that when a user issues the command 'show
interface serial 0', a line is displayed indicating that, 'This is the connection to

Company A.' What interface command would accomplish this?

A.) banner motd #This is the connection to Company A.#
B.) interface This is the connection to Company A. C.) This cannot be done for an
individual interface. D.) description This is the connection to Company A. E.) banner
This is the connection to Company A. F.) display This is the connection to Company A.

Ans D

694. What command would show the version of the IOS that you are running?
A.) show nvram B.) show version C.) show startup-config D.) show ios E.) ver -a F.) show
ram

Ans B

695. When editing a line in the CLI mode, what does 'CTRL-A' do?
A.) Moves you to the previous command.
B.) Moves you to the next word.
C.) Moves you to the end of the line.
D.) Moves you to the next command.
E.) Moves you to the beginning of the line.

Ans E

696. When a router knows the IP address, but does not know the MAC address of the
device it wishes to contact, it uses the ARP (Address resolution protocol) to
determine the MAC address. After it learns the MAC address, it stores this
information in the ARP cache. What is the command to view the ARP cache?
A.) sh mac B.) show cache C.) show arp D.) sh arp interfaces E.) show ip cache

Ans C

697. Which command can verify only Network layer connectivity between 2 hosts?
A.) ping B.)
e-mail C.) plp
D.) arp E.)
telnet

Ans A

698. What would be the first command from global configuration mode to enable
RIP on your router for interface E0, with an address of 181.86.4.4 and mask of

255.255.255.0 ?
A.) router rip B.) network 181.89.4.0 255.255.255.0 C.) router rip int e0 D.) router rip

181.86.0.0 E.) router rip 181.86.4.0 F.) network 181.86.0.0
Ans A

699. Which command would you type to show SAP and RIP updates you are
receiving on an interface?
A.) sh ipx servers B.) sh
ipx traffic C.) sh ipx
interface D.) sh ipx
route

Ans B

700 What is the default IPX Ethernet encapsulation?

A.) SNAP B.) Arpa C.) 802.2 D.) Novell-Ether E.) SAP

Ans D